Last updated at 11/05/2026 04:17:04
10g (4.80mm) Stainless A2-70 G304 Countersunk Phillips (PH2) Self Tapping Screws ANSI B18.6.4
Free delivery between Wed – Fri
10g (4.80mm) x 3/8" Countersunk Phillips (PH2) Self Tapping Screw A2-70 Stainless G304 ANSI B18.6.4
Free delivery between Wed – Fri
originally posted on thefastenerfactory.com.au
Couldn't be happier with quality and value for money. Very quick turn-around time too. I'll be purchasing all my fasteners from here from now on.
originally posted on thefastenerfactory.com.au
Good products, great prices.Online ordering simple and clear.Express delivery really good.Really happy with products and service.Thanks Fastener Factory.
originally posted on thefastenerfactory.com.au
Good quality, but I wish the price was a little lower than I expected. Over all happy with the products.
| Size | 10g (4.80mm) |
| Drive Type | Phillips |
| System of Measurement | Screw Gauge |
| Drive Size | PH2 |
| Head Type | Countersunk Head |
10g (4.80mm) Stainless A2-70 G304 Countersunk Phillips (PH2) Self Tapping Screws ANSI B18.6.4
Free delivery between Wed – Fri
10g (4.80mm) x 3/8" Countersunk Phillips (PH2) Self Tapping Screw A2-70 Stainless G304 ANSI B18.6.4
Free delivery between Wed – Fri
Couldn't be happier with quality and value for money. Very quick turn-around time too. I'll be purchasing all my fasteners from here from now on.
Good products, great prices.Online ordering simple and clear.Express delivery really good.Really happy with products and service.Thanks Fastener Factory.
Good quality, but I wish the price was a little lower than I expected. Over all happy with the products.
Searching for a better price on 200 Stainless Stel Screws than that being offered by the Big Green Shed (Bunnings) I found these guys at The Fastener Factory. Great product, great price and great service. Nice work, thanks for your help.
Great products, good price and fast delivery. +++++
Product exactly as advertised. Prompt delivery and a high quality product.
wont rust and hence will last a long time near the beach. Main use is to replace the nails in some electrical / coax / misting tube clamps by removing the nail and drilling a 3mm hole. Then a cordless drill can drive them into a timber section that would otherwise bend, vibrate etc. with a hammer, due to no supporting structure immediately behind the area that you wish to secure the cable / tube etc.
Hobson’s always a good brand. Delivery from the FF very swift too
Great for mounting MDF shelves on steel countersunk L brackets. The China Emporium don't sell these. (They sell the brackets though).
Terrible quality and screws just kept sheeringI had to use an alternate product -these were a waste of money
| Size | 10g (4.80mm) |
| Drive Type | Phillips |
| System of Measurement | Screw Gauge |
| Drive Size | PH2 |
| Head Type | Countersunk Head |
10g (4.80mm) Stainless A2-70 G304 Countersunk Phillips (PH2) Self Tapper Screws ANSI B18.6.4
Countersunk Phillips Self Tapper screws create (taps) it's own thread as the screw is being driven in. The head is flat with a smooth tapered underside designed to sit flush in fittings with tapered recesses. Suitable for: Can you be used in stainless light gauge steel aluminium certain plastics and timber. To ensure the best result it is recommended to always drill a pilot hole Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. It is highly recommended to use Stainless Steel A4-70 G316 if the product will be used within 300 metres of the coast in the food and chemical industry or within salt spray affected areas. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
Countersunk Phillips Self Tapper screws create (taps) it's own thread as the screw is being driven in. The head is flat with a smooth tapered underside designed to sit flush in fittings with tapered recesses. Suitable for: Can you be used in stainless light gauge steel aluminium certain plastics and timber. To ensure the best result it is recommended to always drill a pilot hole Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. It is highly recommended to use Stainless Steel A4-70 G316 if the product will be used within 300 metres of the coast in the food and chemical industry or within salt spray affected areas. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
Countersunk Phillips Self Tapper screws create (taps) it's own thread as the screw is being driven in. The head is flat with a smooth tapered underside designed to sit flush in fittings with tapered recesses. Suitable for: Can you be used in stainless light gauge steel aluminium certain plastics and timber. To ensure the best result it is recommended to always drill a pilot hole Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. It is highly recommended to use Stainless Steel A4-70 G316 if the product will be used within 300 metres of the coast in the food and chemical industry or within salt spray affected areas. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
Countersunk Phillips Self Tapper screws create (taps) it's own thread as the screw is being driven in. The head is flat with a smooth tapered underside designed to sit flush in fittings with tapered recesses. Suitable for: Can you be used in stainless light gauge steel aluminium certain plastics and timber. To ensure the best result it is recommended to always drill a pilot hole Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. It is highly recommended to use Stainless Steel A4-70 G316 if the product will be used within 300 metres of the coast in the food and chemical industry or within salt spray affected areas. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
in 2 offers
The lowest price for 10g (4.80mm) Stainless A2-70 G304 Countersunk Phillips (PH2) Self Tapper Screws ANSI B18.6.4 right now is $5.00 at Bolt & Nut Australia.
The all-time low was $4.00 on 30 July 2025 — today's price is 25% above the lowest ever. It has been notably cheaper before — worth setting a price alert.
Prices last updated 11 May 2026.
