【Impact and Heat Resistant】 - OVERTURE ABS filament 1.75mm is a very durable material engineered to reduce jamming. It provides high heat resistance (Vicat Softening Temperature: 104 ̊C) and good mechanical properties. It's a good choice for functional parts that require durability or high temperature resistance 【Higher Stability】 - OVERTURE 1.75 ABS Filament is made with a specialty ABS resin, which has significantly lower volatile content compared to traditional ABS resins. 1.75 ABS filament requires a heat-bed and a proper printing surface to avoid warping. Big parts are prone to warp in domestic printers and odor when printed is stronger than with PLA. Using raft or brim or reduce the speed for the first layer could help avoid warping 【Printing Settings】 - Nozzle: 245 ̊C - 265 ̊C; Bed: 80 ̊C - 100 ̊C; Speed: 30mm/s - 70mm/s; Bed Surface: BuildTak, PEI sheet with ABS slurry; Cooling Fan: LOW for better surface quality, OFF for better strength "Note: The recommended print setup for Overture filaments could be slightly different from other filaments; Pls read the description below, you may also get some practical suggestions through QA/ Top Review from others. FAQs: Why can't the filaments stick to the build bed? 1. Check the temperature setting before printing, ABS filaments have higher extrusion temperature; 2. Check if the plate surface has been used for a longtime, it is recommended to replace it with our new one to ensure an strong first layer adhesion ; 3. If the first layer has poor adhesion, it is recommended to re-level the print substrate to reduce the distance between the nozzle and the surface plate; 4. If the effect is not good, it is recommended to try printing the draft before printing. Specification: Recommended Extrusion/Nozzle Temp: 245 °C - 265°C (473°F~ 509°F ), Heated Bed Temp: 80°C - 100 °C (176°F~ 212°F)/ PVP stick helps Printing Speed:30~70 mm/s (1,800~4,200mm/ min) Fan: Low for better surface quality; Off for better strength Raft Filaments Diameter and Accuracy: 1.75 mm +/- 0.05 Filaments Net Weight: 1 kg (2.2 lbs) Packaging Included: 1 × spool of ABS filaments"
【Impact and Heat Resistant】 - OVERTURE ABS filament 1.75mm is a very durable material engineered to reduce jamming. It provides high heat resistance (Vicat Softening Temperature: 104 ̊C) and good mechanical properties. It's a good choice for functional parts that require durability or high temperature resistance 【Higher Stability】 - OVERTURE 1.75 ABS Filament is made with a specialty ABS resin, which has significantly lower volatile content compared to traditional ABS resins. 1.75 ABS filament requires a heat-bed and a proper printing surface to avoid warping. Big parts are prone to warp in domestic printers and odor when printed is stronger than with PLA. Using raft or brim or reduce the speed for the first layer could help avoid warping 【Printing Settings】 - Nozzle: 245 ̊C - 265 ̊C; Bed: 80 ̊C - 100 ̊C; Speed: 30mm/s - 70mm/s; Bed Surface: BuildTak, PEI sheet with ABS slurry; Cooling Fan: LOW for better surface quality, OFF for better strength "Note: The recommended print setup for Overture filaments could be slightly different from other filaments; Pls read the description below, you may also get some practical suggestions through QA/ Top Review from others. FAQs: Why can't the filaments stick to the build bed? 1. Check the temperature setting before printing, ABS filaments have higher extrusion temperature; 2. Check if the plate surface has been used for a longtime, it is recommended to replace it with our new one to ensure an strong first layer adhesion ; 3. If the first layer has poor adhesion, it is recommended to re-level the print substrate to reduce the distance between the nozzle and the surface plate; 4. If the effect is not good, it is recommended to try printing the draft before printing. Specification: Recommended Extrusion/Nozzle Temp: 245 °C - 265°C (473°F~ 509°F ), Heated Bed Temp: 80°C - 100 °C (176°F~ 212°F)/ PVP stick helps Printing Speed:30~70 mm/s (1,800~4,200mm/ min) Fan: Low for better surface quality; Off for better strength Raft Filaments Diameter and Accuracy: 1.75 mm +/- 0.05 Filaments Net Weight: 1 kg (2.2 lbs) Packaging Included: 1 × spool of ABS filaments"
in 1 offers
【Impact and Heat Resistant】 - OVERTURE ABS filament 1.75mm is a very durable material engineered to reduce jamming. It provides high heat resistance (Vicat Softening Temperature: 104 ̊C) and good mechanical properties. It's a good choice for functional parts that require durability or high temperature resistance 【Higher Stability】 - OVERTURE 1.75 ABS Filament is made with a specialty ABS resin, which has significantly lower volatile content compared to traditional ABS resins. 1.75 ABS filament requires a heat-bed and a proper printing surface to avoid warping. Big parts are prone to warp in domestic printers and odor when printed is stronger than with PLA. Using raft or brim or reduce the speed for the first layer could help avoid warping 【Printing Settings】 - Nozzle: 245 ̊C - 265 ̊C; Bed: 80 ̊C - 100 ̊C; Speed: 30mm/s - 70mm/s; Bed Surface: BuildTak, PEI sheet with ABS slurry; Cooling Fan: LOW for better surface quality, OFF for better strength "Note: The recommended print setup for Overture filaments could be slightly different from other filaments; Pls read the description below, you may also get some practical suggestions through QA/ Top Review from others. FAQs: Why can't the filaments stick to the build bed? 1. Check the temperature setting before printing, ABS filaments have higher extrusion temperature; 2. Check if the plate surface has been used for a longtime, it is recommended to replace it with our new one to ensure an strong first layer adhesion ; 3. If the first layer has poor adhesion, it is recommended to re-level the print substrate to reduce the distance between the nozzle and the surface plate; 4. If the effect is not good, it is recommended to try printing the draft before printing. Specification: Recommended Extrusion/Nozzle Temp: 245 °C - 265°C (473°F~ 509°F ), Heated Bed Temp: 80°C - 100 °C (176°F~ 212°F)/ PVP stick helps Printing Speed:30~70 mm/s (1,800~4,200mm/ min) Fan: Low for better surface quality; Off for better strength Raft Filaments Diameter and Accuracy: 1.75 mm +/- 0.05 Filaments Net Weight: 1 kg (2.2 lbs) Packaging Included: 1 × spool of ABS filaments"
【Impact and Heat Resistant】 - OVERTURE ABS filament 1.75mm is a very durable material engineered to reduce jamming. It provides high heat resistance (Vicat Softening Temperature: 104 ̊C) and good mechanical properties. It's a good choice for functional parts that require durability or high temperature resistance 【Higher Stability】 - OVERTURE 1.75 ABS Filament is made with a specialty ABS resin, which has significantly lower volatile content compared to traditional ABS resins. 1.75 ABS filament requires a heat-bed and a proper printing surface to avoid warping. Big parts are prone to warp in domestic printers and odor when printed is stronger than with PLA. Using raft or brim or reduce the speed for the first layer could help avoid warping 【Printing Settings】 - Nozzle: 245 ̊C - 265 ̊C; Bed: 80 ̊C - 100 ̊C; Speed: 30mm/s - 70mm/s; Bed Surface: BuildTak, PEI sheet with ABS slurry; Cooling Fan: LOW for better surface quality, OFF for better strength "Note: The recommended print setup for Overture filaments could be slightly different from other filaments; Pls read the description below, you may also get some practical suggestions through QA/ Top Review from others. FAQs: Why can't the filaments stick to the build bed? 1. Check the temperature setting before printing, ABS filaments have higher extrusion temperature; 2. Check if the plate surface has been used for a longtime, it is recommended to replace it with our new one to ensure an strong first layer adhesion ; 3. If the first layer has poor adhesion, it is recommended to re-level the print substrate to reduce the distance between the nozzle and the surface plate; 4. If the effect is not good, it is recommended to try printing the draft before printing. Specification: Recommended Extrusion/Nozzle Temp: 245 °C - 265°C (473°F~ 509°F ), Heated Bed Temp: 80°C - 100 °C (176°F~ 212°F)/ PVP stick helps Printing Speed:30~70 mm/s (1,800~4,200mm/ min) Fan: Low for better surface quality; Off for better strength Raft Filaments Diameter and Accuracy: 1.75 mm +/- 0.05 Filaments Net Weight: 1 kg (2.2 lbs) Packaging Included: 1 × spool of ABS filaments"
Last updated at 11/11/2024 10:08:59
+ $7.99 delivery
Go to store
Affiliate Disclosure: We may receive a small commission for purchases made through this link at no extra cost to you. This helps support our site. Thank you!
| Item diameter | 1.75 Millimeters |
Updated about 23 hours ago
| Item diameter | 1.75 Millimeters |
