PCIe Gen 3x4 interface with read speeds up to 2,200MB/s and write speeds up to 1,600MB/s LDPC (Low-Density Parity Check) error correction code (ECC) technology, End-To-End (E2E) data protection, and RAID engine for enhanced data integrity and stability Supports NVMe 1.3, Host Memory Buffer (HMB), and SLC Cache to deliver high and efficient performance Small form factor M.2 2280 (80mm) allows for easy installation in laptops, small form factor PC systems, and some ultrabooks Massive storage capacity options up to 2TB The P34A60 is an affordable storage solution that doesn't skimp on performance. It's designed for novice users, DIY system builders, purpose-built system manufacturers, and simply those who are looking to upgrade their PC. But with a PCIe Gen3x4 interface, which means four lanes are used for transmitting and receiving data simultaneously, This SSD is anything but basic. The P34A60 supports NVMe 1.3, which demands better performance vectors than AHCI (Advanced Host Controller Interface), including scalable bandwidth, increased IOPS, and low latency. In addition, HMB (Host Memory Buffer) architecture, which allows the host driver to allocate system memory (RAM) for exclusive use by the SSD, results in higher efficiency. It's this teamwork that provides optimum performance. The P34A60 is engineered with LDPC (Low-Density Parity Check) coding, a powerful error correction code (ECC) algorithm, to keep data secure. Furthermore, End-To-End (E2E) data protection, to ensure that accessed and retrieved data are correct from start to finish, and a RAID engine, which provides an acceptable level of fault tolerance, work to enhance data integrity for greater reliability and stability. With an M.2 2280 (80mm) form factor, the P34A60's compact size allows for easy installation in laptops, small form factor PC systems, and some ultrabooks. And with up to a massive 2TB capacity option, it's an easy upgrade that can greatly expand your system's storage potential while also saving space for other components.
PCIe Gen 3x4 interface with read speeds up to 2,200MB/s and write speeds up to 1,600MB/s LDPC (Low-Density Parity Check) error correction code (ECC) technology, End-To-End (E2E) data protection, and RAID engine for enhanced data integrity and stability Supports NVMe 1.3, Host Memory Buffer (HMB), and SLC Cache to deliver high and efficient performance Small form factor M.2 2280 (80mm) allows for easy installation in laptops, small form factor PC systems, and some ultrabooks Massive storage capacity options up to 2TB The P34A60 is an affordable storage solution that doesn't skimp on performance. It's designed for novice users, DIY system builders, purpose-built system manufacturers, and simply those who are looking to upgrade their PC. But with a PCIe Gen3x4 interface, which means four lanes are used for transmitting and receiving data simultaneously, This SSD is anything but basic. The P34A60 supports NVMe 1.3, which demands better performance vectors than AHCI (Advanced Host Controller Interface), including scalable bandwidth, increased IOPS, and low latency. In addition, HMB (Host Memory Buffer) architecture, which allows the host driver to allocate system memory (RAM) for exclusive use by the SSD, results in higher efficiency. It's this teamwork that provides optimum performance. The P34A60 is engineered with LDPC (Low-Density Parity Check) coding, a powerful error correction code (ECC) algorithm, to keep data secure. Furthermore, End-To-End (E2E) data protection, to ensure that accessed and retrieved data are correct from start to finish, and a RAID engine, which provides an acceptable level of fault tolerance, work to enhance data integrity for greater reliability and stability. With an M.2 2280 (80mm) form factor, the P34A60's compact size allows for easy installation in laptops, small form factor PC systems, and some ultrabooks. And with up to a massive 2TB capacity option, it's an easy upgrade that can greatly expand your system's storage potential while also saving space for other components.
Silicon Power 1TB NVMe PCIe Gen3x4 M.2 2280 TLC SSD R/W Up to 2,200MB/s and 1,600MB/s (SU001TBP34A60M28UA)
PCIe Gen 3x4 interface with read speeds up to 2,200MB/s and write speeds up to 1,600MB/s LDPC (Low-Density Parity Check) error correction code (ECC) technology, End-To-End (E2E) data protection, and RAID engine for enhanced data integrity and stability Supports NVMe 1.3, Host Memory Buffer (HMB), and SLC Cache to deliver high and efficient performance Small form factor M.2 2280 (80mm) allows for easy installation in laptops, small form factor PC systems, and some ultrabooks Massive storage capacity options up to 2TB The P34A60 is an affordable storage solution that doesn't skimp on performance. It's designed for novice users, DIY system builders, purpose-built system manufacturers, and simply those who are looking to upgrade their PC. But with a PCIe Gen3x4 interface, which means four lanes are used for transmitting and receiving data simultaneously, This SSD is anything but basic. The P34A60 supports NVMe 1.3, which demands better performance vectors than AHCI (Advanced Host Controller Interface), including scalable bandwidth, increased IOPS, and low latency. In addition, HMB (Host Memory Buffer) architecture, which allows the host driver to allocate system memory (RAM) for exclusive use by the SSD, results in higher efficiency. It's this teamwork that provides optimum performance. The P34A60 is engineered with LDPC (Low-Density Parity Check) coding, a powerful error correction code (ECC) algorithm, to keep data secure. Furthermore, End-To-End (E2E) data protection, to ensure that accessed and retrieved data are correct from start to finish, and a RAID engine, which provides an acceptable level of fault tolerance, work to enhance data integrity for greater reliability and stability. With an M.2 2280 (80mm) form factor, the P34A60's compact size allows for easy installation in laptops, small form factor PC systems, and some ultrabooks. And with up to a massive 2TB capacity option, it's an easy upgrade that can greatly expand your system's storage potential while also saving space for other components.
PCIe Gen 3x4 interface with read speeds up to 2,200MB/s and write speeds up to 1,600MB/s LDPC (Low-Density Parity Check) error correction code (ECC) technology, End-To-End (E2E) data protection, and RAID engine for enhanced data integrity and stability Supports NVMe 1.3, Host Memory Buffer (HMB), and SLC Cache to deliver high and efficient performance Small form factor M.2 2280 (80mm) allows for easy installation in laptops, small form factor PC systems, and some ultrabooks Massive storage capacity options up to 2TB The P34A60 is an affordable storage solution that doesn't skimp on performance. It's designed for novice users, DIY system builders, purpose-built system manufacturers, and simply those who are looking to upgrade their PC. But with a PCIe Gen3x4 interface, which means four lanes are used for transmitting and receiving data simultaneously, This SSD is anything but basic. The P34A60 supports NVMe 1.3, which demands better performance vectors than AHCI (Advanced Host Controller Interface), including scalable bandwidth, increased IOPS, and low latency. In addition, HMB (Host Memory Buffer) architecture, which allows the host driver to allocate system memory (RAM) for exclusive use by the SSD, results in higher efficiency. It's this teamwork that provides optimum performance. The P34A60 is engineered with LDPC (Low-Density Parity Check) coding, a powerful error correction code (ECC) algorithm, to keep data secure. Furthermore, End-To-End (E2E) data protection, to ensure that accessed and retrieved data are correct from start to finish, and a RAID engine, which provides an acceptable level of fault tolerance, work to enhance data integrity for greater reliability and stability. With an M.2 2280 (80mm) form factor, the P34A60's compact size allows for easy installation in laptops, small form factor PC systems, and some ultrabooks. And with up to a massive 2TB capacity option, it's an easy upgrade that can greatly expand your system's storage potential while also saving space for other components.
in 2 offers
The lowest price for Silicon Power 1TB NVMe PCIe Gen3x4 M.2 2280 TLC SSD R/W Up to 2,200MB/s and 1,600MB/s (SU001TBP34A60M28UA) right now is $82.00.
Prices last updated 21 Sept 2025.
Last updated at 21/09/2025 09:40:40
originally posted on shopee.com.my
Performance:2TB: 1.8TBIt fits well. Will buy from seller again if i need it in the future.If unsure if this is the right ssd you're looking for, i strongly advice you to check and double confirm your spec first before you buy.Ps: if u have installed but it doesnt show up dont worry, dont panic. Go to device manager, then to your hard drive, there should be two storage displays the original and one unrecognised new ssd. Just set the status to online and it should work just fine.
originally posted on shopee.com.my
Performance:ExcellentInstalled the M.2, running smoothly and working perfectly without any error occur. No bluescreen or anything. Feels like I'm using a new laptop. Installed windows 10 on it. Speed is very fast. The price is cheap and reasonable. Been using one of their sata SSD for a year now and there's no problem with it. Very good and durable products. Would recommend to others. I give rating 10/10. Delivery is fast. Customer support is good and helpful.
originally posted on newegg.com
***** CrystalDiskMark 6.0.2 Seq. Read: 3414 MB/s CrystalDiskMark 6.0.2 Seq. Write: 2079 MB/s AS SSD Seq. Read: 2947 MB/s AS SSD Seq. Write: 1952 MB/s Temp Idle: 38 C Temp Load: 51 C Gigabyte AB350M-DS3H SeaSonic X650 Ryzen 5 1600 Team Group Vulcan DDR4 3200 PowerColor RX 470 Silicon Power P34A80 512 GB NVMe SSD Team Group L5 Lite 480 GB SSD Windows 10 Pro Rosewill Midtower case P.S. NOTE ON LOW WRITE SPEEDS I noticed that after a hard reset (black screen from overclocking), this drive would not write at full speeds (CrystalDiskMark Seq. Write 640 MB/s). I believe this was due to Windows 10 disabling write caching on the drive. Here is how I corrected the problem. Open: Device Manager> Disk Drives> SPCC M.2 PCIe SSD> SPCC M.2 PCIe SSD Properties> Policies In ... More***** CrystalDiskMark 6.0.2 Seq. Read: 3414 MB/s CrystalDiskMark 6.0.2 Seq. Write: 2079 MB/s AS SSD Seq. Read: 2947 MB/s AS SSD Seq. Write: 1952 MB/s Temp Idle: 38 C Temp Load: 51 C Gigabyte AB350M-DS3H SeaSonic X650 Ryzen 5 1600 Team Group Vulcan DDR4 3200 PowerColor RX 470 Silicon Power P34A80 512 GB NVMe SSD Team Group L5 Lite 480 GB SSD Windows 10 Pro Rosewill Midtower case P.S. NOTE ON LOW WRITE SPEEDS I noticed that after a hard reset (black screen from overclocking), this drive would not write at full speeds (CrystalDiskMark Seq. Write 640 MB/s). I believe this was due to Windows 10 disabling write caching on the drive. Here is how I corrected the problem. Open: Device Manager> Disk Drives> SPCC M.2 PCIe SSD> SPCC M.2 PCIe SSD Properties> Policies In Policies, toggle both boxes "Enable write caching on the device", and "Turn off Windows write-cache buffer flushing on the device" (toggle a few times). MAKE SURE BOTH BOXES ARE CHECKED and click "OK". Keep Device Manager open and run your benchmark to see if write speeds are back to spec. If everything is good, go back into: SPCC M.2 PCIe SSD Properties> Policies UNCHECK BOX "Turn off Windows write-cache buffer flushing on the device" (so as to not have a power outage corrupt Windows). Click "OK". Run your bench again to see if drive is still up to spec. Good luck on your mission, Jim. :) P.P.S. Bought a second one for my daughter's new computer, and it works just as well as the first one. System: ASUS ROG STRIX X370 -F GAMING Antec True Power Classic 750 PSU Ryzen 5 1600 GEIL Evo Potenza AMD 16 GB (2x8) DDR4 3000 Power Color Red Devil RX 470 Silicon Power P34A80 512 GB NVMe SSD SK Hynix 500 GB SATA III SSD 4 pack Cooler Master 120mm case fans (the ketchup and mustard specials) Rosewill Case
| Digital storage capacity | 1000 GB |
| Compatible devices | Laptop, Desktop |
| Hard disk interface | ATA-4 |
| Connectivity technology | SATA |
| Hard disk size | 13 GB |
Performance:2TB: 1.8TBIt fits well. Will buy from seller again if i need it in the future.If unsure if this is the right ssd you're looking for, i strongly advice you to check and double confirm your spec first before you buy.Ps: if u have installed but it doesnt show up dont worry, dont panic. Go to device manager, then to your hard drive, there should be two storage displays the original and one unrecognised new ssd. Just set the status to online and it should work just fine.
Performance:ExcellentInstalled the M.2, running smoothly and working perfectly without any error occur. No bluescreen or anything. Feels like I'm using a new laptop. Installed windows 10 on it. Speed is very fast. The price is cheap and reasonable. Been using one of their sata SSD for a year now and there's no problem with it. Very good and durable products. Would recommend to others. I give rating 10/10. Delivery is fast. Customer support is good and helpful.
***** CrystalDiskMark 6.0.2 Seq. Read: 3414 MB/s CrystalDiskMark 6.0.2 Seq. Write: 2079 MB/s AS SSD Seq. Read: 2947 MB/s AS SSD Seq. Write: 1952 MB/s Temp Idle: 38 C Temp Load: 51 C Gigabyte AB350M-DS3H SeaSonic X650 Ryzen 5 1600 Team Group Vulcan DDR4 3200 PowerColor RX 470 Silicon Power P34A80 512 GB NVMe SSD Team Group L5 Lite 480 GB SSD Windows 10 Pro Rosewill Midtower case P.S. NOTE ON LOW WRITE SPEEDS I noticed that after a hard reset (black screen from overclocking), this drive would not write at full speeds (CrystalDiskMark Seq. Write 640 MB/s). I believe this was due to Windows 10 disabling write caching on the drive. Here is how I corrected the problem. Open: Device Manager> Disk Drives> SPCC M.2 PCIe SSD> SPCC M.2 PCIe SSD Properties> Policies In ... More***** CrystalDiskMark 6.0.2 Seq. Read: 3414 MB/s CrystalDiskMark 6.0.2 Seq. Write: 2079 MB/s AS SSD Seq. Read: 2947 MB/s AS SSD Seq. Write: 1952 MB/s Temp Idle: 38 C Temp Load: 51 C Gigabyte AB350M-DS3H SeaSonic X650 Ryzen 5 1600 Team Group Vulcan DDR4 3200 PowerColor RX 470 Silicon Power P34A80 512 GB NVMe SSD Team Group L5 Lite 480 GB SSD Windows 10 Pro Rosewill Midtower case P.S. NOTE ON LOW WRITE SPEEDS I noticed that after a hard reset (black screen from overclocking), this drive would not write at full speeds (CrystalDiskMark Seq. Write 640 MB/s). I believe this was due to Windows 10 disabling write caching on the drive. Here is how I corrected the problem. Open: Device Manager> Disk Drives> SPCC M.2 PCIe SSD> SPCC M.2 PCIe SSD Properties> Policies In Policies, toggle both boxes "Enable write caching on the device", and "Turn off Windows write-cache buffer flushing on the device" (toggle a few times). MAKE SURE BOTH BOXES ARE CHECKED and click "OK". Keep Device Manager open and run your benchmark to see if write speeds are back to spec. If everything is good, go back into: SPCC M.2 PCIe SSD Properties> Policies UNCHECK BOX "Turn off Windows write-cache buffer flushing on the device" (so as to not have a power outage corrupt Windows). Click "OK". Run your bench again to see if drive is still up to spec. Good luck on your mission, Jim. :) P.P.S. Bought a second one for my daughter's new computer, and it works just as well as the first one. System: ASUS ROG STRIX X370 -F GAMING Antec True Power Classic 750 PSU Ryzen 5 1600 GEIL Evo Potenza AMD 16 GB (2x8) DDR4 3000 Power Color Red Devil RX 470 Silicon Power P34A80 512 GB NVMe SSD SK Hynix 500 GB SATA III SSD 4 pack Cooler Master 120mm case fans (the ketchup and mustard specials) Rosewill Case
I have purchased several of these Silicon Power 2TB M.2 2280 NVMe PCIe TLC SSD's for upgrading client PC's (HP Elitebook 840 G3 & G4 notebooks). I get similar speed performance compared to the Samsung 970 EVO Plus SSD's but the specs indicate that the Silicon Power SSD's have a longer MTBF and Warranty. Since These SSD's are main OS drives in i7 notebooks with applications where there are a lot of read/write cycles, I prefer the TLC NAND SSD's which can sustain (supposedly) a greater number of read/write cycles before cell failure. Length of ownership has not been long enough to make a true assessment of longevity. I can only state that of the four SSD's purchased, none had infant mortality. The temperature of the SSD is no higher than that of any other M.2 2280 ... MoreI have purchased several of these Silicon Power 2TB M.2 2280 NVMe PCIe TLC SSD's for upgrading client PC's (HP Elitebook 840 G3 & G4 notebooks). I get similar speed performance compared to the Samsung 970 EVO Plus SSD's but the specs indicate that the Silicon Power SSD's have a longer MTBF and Warranty. Since These SSD's are main OS drives in i7 notebooks with applications where there are a lot of read/write cycles, I prefer the TLC NAND SSD's which can sustain (supposedly) a greater number of read/write cycles before cell failure. Length of ownership has not been long enough to make a true assessment of longevity. I can only state that of the four SSD's purchased, none had infant mortality. The temperature of the SSD is no higher than that of any other M.2 2280 NVMe SSD that I have installed (Samsung, WD, Intel, Crucial) so, hopefully, these will last a long time. I normally do fresh installs of the OS and drivers on the notebooks. The HP Elitebooks recognize the Win 10 OS immediately even after changing out the RAM and the SSD. Windows 7 installs still require a product key for install (Just like always). If I have to clone the OS drive, I use Macrium Reflect; even for Samsung SSD's since Samsung Magician has a bad reputation for drive cloning (just what I have read and heard from others so YMMV). In conclusion, I would recommend these SSD's and have purchased them several times.they are a great value when compared to other reputable Gen 3X4 PCIe M.2 2280 NVMe SSD's.
I bought this Hard drive to use as a large capacity storage drive for video files, things I wanted to be able to access quickly for editing. However after about a month of infrequent use it started to have serious problems. First it started to randomly stop transferring files for a few seconds before resuming. Then a while after that it would stop transferring files and never resume again at which point my PC would return an error about the drive no longer existing, except it was still listed on the "This PC" screen. If I tried to open the drive again and move files then the transfer would stay at 0% permanently. I've worked in IT and went through everything I could think of to make sure it wasn't an issue on the side of my computer and the problem persisted. I've ... MoreI bought this Hard drive to use as a large capacity storage drive for video files, things I wanted to be able to access quickly for editing. However after about a month of infrequent use it started to have serious problems. First it started to randomly stop transferring files for a few seconds before resuming. Then a while after that it would stop transferring files and never resume again at which point my PC would return an error about the drive no longer existing, except it was still listed on the "This PC" screen. If I tried to open the drive again and move files then the transfer would stay at 0% permanently. I've worked in IT and went through everything I could think of to make sure it wasn't an issue on the side of my computer and the problem persisted. I've also tried reformatting the drive; this worked for a few transfers, but the problem returned exactly as it was before so these few successful transfers may have just been a fluke. At this point I'm assuming the drive is faulty; considering the price this is a huge disappointment.
| Digital storage capacity | 1000 GB |
| Compatible devices | Laptop, Desktop |
| Hard disk interface | ATA-4 |
| Connectivity technology | SATA |
| Hard disk size | 13 GB |
